大板瓷磚裝飾效果簡潔氣派，留縫少，切割方式多使其運用更加廣泛。So，大板如何鋪貼效果更佳呢？這里有份詳細的大板鋪貼講解，建議收藏！

The decorative effect of the large tile is simple and elegant, with fewer seams and more cutting methods, which makes it more widely used. So, how to lay the board better? Here is a detailed explanation of the large board, it is recommended to collect!

01、準備工作

鋪貼之前，我們需要準備好鋪貼大規格瓷磚的工具，如粘結劑、三孔玻璃吸、鋸齒狀抹灰器、灰匙、橡膠錘、靠尺、找平鉗套裝、清潔抹布等。

Before paving, we need to prepare tools for laying large-sized tiles, such as adhesives, three-hole glass suction, serrated plaster, ash spoon, rubber hammer, ruler, leveling pliers set, cleaning rag, etc.

02、鋪貼前檢查

施工圖紙校對、平整度檢測、垂直度檢測、水電管線鋪設檢測以及防水等工作，這是確保最佳的瓷磚鋪設效果、打造高品質生活空間的前置條件。

Construction drawings proofreading, flatness detection, verticality detection, water and electricity pipeline laying detection and waterproofing are the prerequisites for ensuring the best tile laying effect and creating a high-quality living space.

03、基面處理

清除基層浮灰、油等污漬，以免會影響粘結劑的粘合度。基面內部必須保持平整，高低不平或表面粗糙的地方可以使用水泥砂漿抹平，同時充分濕潤施工基面，防止空鼓。

Remove the dirt, oil and other stains from the base, so as not to affect the adhesion of the adhesive. The interior of the base surface must be kept flat. Cement mortar can be used to smooth the uneven or rough surface, and at the same time fully wet the construction base to prevent emptying.

04、調制粘結劑

1. 將自來水加入攪拌桶，再將粘貼劑逐量加入，用低速電動攪拌器攪拌均勻成糊狀。

2. 水化（靜置）5-10min后進行二次攪拌3min左右即可使用，(水化后的粘結劑不可加水或粘結劑干粉再次攪拌，否則影響粘結效果)

3. 用批灰刀挑起攪拌均勻的粘結劑后倒置，粘結劑在5秒左右從批灰刀上墜落，此時的粘結劑的粘稠度為最佳。

注意：粘結劑在制備完畢后需靜置5-10min。粘結劑的可操作時間常溫下為2小時。（可操作時間指制備完畢到使用的時間）。

1. Add tap water to the mixing tank, and then add the adhesive one by one, using a low-speed electric mixer to mix evenly into a paste.

2. After hydration (stand still) for 5-10 minutes, it can be used after about 2 minutes of secondary stirring. (The hydrated adhesive cannot be added with water or the dry powder of the adhesive is stirred again, otherwise it will affect the bonding effect)

3. Use the batch ash knife to pick up the evenly mixed adhesive and turn it upside down. The adhesive falls from the batch ash knife in about 5 seconds. At this time, the viscosity of the adhesive is the best.

Note: The adhesive needs to stand for 5-10min after preparation. The operable time of the adhesive is 2 hours at room temperature. (Operable time refers to the time from preparation to use).

05、涂抹粘結劑

在地面均勻鋪上一層粘結劑，形成半干的一層，再次用粘結劑填平表面凹凸處，厚度為0.5CM左右；適當條件下，可同時將粘結劑均勻地抹在瓷磚背面，涂抹飽滿。

Spread a layer of adhesive evenly on the ground to form a semi-dry layer, and then fill the surface irregularities with the adhesive again, the thickness is about 0.5CM; under appropriate conditions, the adhesive can be evenly applied to the tiles at the same time On the back, smear full.

瓷磚背涂時，需用齒狀抹灰器均勻的將粘結劑抹成條齒狀。注意刮時基面與大板需朝同一方向刮齒紋，便于空氣排出，避免空鼓而造成開裂脫落現象。

When the tiles are back-coated, the adhesive needs to be evenly applied to the teeth with a tooth plaster. Note that the base surface and the large board should be scraped in the same direction when scraping, which is convenient for the air to escape and avoid the phenomenon of cracking and shedding caused by the hollow drum.

06、搬運鋪貼

用三孔玻璃吸工具平抬大板平移施工位置，放置到鋪好粘結劑的基面上，至少需要2名工人進行搬運；面積更大的使用移動架搬運。

Use a three-hole glass suction tool to lift the large plate and move it to the construction position, and place it on the base surface where the adhesive is paved. At least 2 workers are required to carry it; for a larger area, use a moving frame to carry it.

大板的粘貼順序為“自內而外”，必須保證粘結劑的飽滿度，避免出現空鼓現象。根據設計的要求，應使用適當規格的定位器，以保證留縫的尺寸滿足設計要求，并保證留縫寬度的一致。

The order of pasting the large board is "from the inside out", and the fullness of the adhesive must be ensured to avoid emptying. According to the design requirements, the locator with appropriate specifications should be used to ensure that the size of the remaining seam meets the design requirements and that the width of the remaining seam is consistent.

07、鋪平壓緊

將瓷磚平整地鋪貼在基層上，使用橡膠錘或塑膠平板將瓷磚拍實鋪平，便于大板瓷磚與基面之間滿漿，排出氣泡，以免產生空鼓現象。

注意已經鋪貼完成的大板瓷磚表面拍打時一定要控制好力度，拍打方向可以遵循從瓷磚中間往四周擴散進行。用橡膠錘或塑膠平板把磚面敲平整的同時，以靠尺測量，確保瓷磚鋪貼水平。

Lay the tile flat on the base layer, use a rubber hammer or a plastic plate to flatten the tile, so that the large board ceramic tile and the base surface are full of slurry, and the air bubbles are discharged to avoid emptying.

Note that the surface of the large slab tile that has been paved must be well controlled. The direction of the tapping can follow the diffusion from the middle of the tile to the surrounding. Use a rubber hammer or a plastic plate to knock the brick surface flat and measure with a ruler to ensure that the tiles are level.

08、找平處理

在已定位好的大板邊緣周圍每60cm左右插入找平器底座，檢驗平整后插入找平楔子并夾緊找平器，調節相鄰大板的表面平整度，并將大板間隙調整為2mm左右，以便后續美縫劑處理。

Insert the leveler base around every 60cm around the edge of the positioned large board, insert the leveling wedge and clamp the leveler after checking the leveling, adjust the surface flatness of the adjacent large board, and adjust the large board gap to about 2mm, so that Subsequent beauty agent treatment.

09、空鼓檢查

鋪貼一個小時后，可用橡膠錘敲擊磚面，檢查是否出現空鼓現象。若聽到“空空”聲的地磚，必須設法重新鋪貼。瓷磚鋪貼結束后24小時，可進行嵌縫施工。

After paving for an hour, you can use a rubber hammer to hit the brick surface to check whether there is hollow phenomenon. If you hear "empty" sound tiles, you must try to re-paving. The caulking construction can be carried out 24 hours after the tile laying is finished.

10、磚面清潔

及時將殘留的粘結劑和灰塵沙土清潔干凈，鋪貼24小時后才能進行美縫。美縫可使用海綿填縫刮刀對瓷磚縫隙進行美縫處理，等待填縫劑固化后，清理多余的美縫劑。

Clean the residual adhesive and dust, sand and dirt in time, and beautify the seam only after 24 hours of application. Beauty joints can use a sponge caulking spatula to perform beauty joint treatment on the gaps of ceramic tiles.

11、施工小貼士

1.在大板鋪貼施工時，建議使用專業的粘結劑，而非傳統【水泥】，因為使用水泥鋪貼大板容易造成空鼓現象。

2.鋪貼厚度以5-7毫米為宜，粘結劑過厚容易導致后期脫落。

3.鋪貼高度如超過7.2米，建議使用干掛法。

4.建議使用美縫劑/瓷縫劑，能夠增加瓷磚的整體美觀感，不會霉變。

完成這些工序后，整個大板的鋪貼操作步驟就圓滿的完成啦！

1. In the construction of large slabs, it is recommended to use professional adhesives instead of traditional [cement], because the use of cement to lay large slabs can easily cause hollowing.

2. The thickness of the paving should be 5-7 mm, too thick adhesive can easily lead to falling off later.

3. If the paving height exceeds 7.2 meters, the dry hanging method is recommended.

4. It is recommended to use the beauty jointing agent/porcelain jointing agent, which can increase the overall aesthetic appearance of the ceramic tile without being moldy.

After completing these procedures, the entire slab laying operation step is successfully completed!

大板裝卸物流指導

1、為確保產品完好無損，可以按照以下裝卸與物流標準進行操作。

△使用2噸以上叉車并用加長叉，叉長要求達到1.2米

△每次只能叉一托，豎向必須用加長叉

△不同規格不可壓放

2、裝車注意

◎ 按要求打好簡易托，確保產品完好無損，裝車前拍照

◎ 運輸車輛噸位是否符合裝車運輸標準

◎ 裝車叉車噸位與叉長需符合標準

◎ 貨物裝車需按各規格裝車標準嚴格執行，運輸途中不能疊放其他貨物

3、運輸注意

◎ 屬于易碎品，勿踩、勿壓

◎ 貨物裝車后不能進行二次卸載與重新裝車，避免破損

◎ 車速穩定，勻速行駛

4、卸車注意

◎ 卸貨前拍照，卸貨叉車噸位與叉長需符合標準